Move Close
Welcome to zx14ninjaform.com!

You are not logged in.
New Topic Reply
Next Page

Page: 1

Previous Page

Thread: runnining issuses

Created on: 07/21/09 09:22 AM

Replies: 4

scottjkyl


scottjkyl's Gravatar

Location: east jordan,mi

Joined: 06/26/09

Posts: 1851

runnining issuses
07/21/09 9:22 AM

i have a 08 14 has m4 slip-ons k&n filter and factory pro velocity stacks (mids) and pc3 with m4 stock or aftermarket map. bike is new (3 mo. old) 1500 miles. problem is now all of a sudden when bike get warm it runs and sounds like a v twin and stalls out when downshifting at idle it runs at 1000rpm 500 rpm lower than its suppossed too. i can start up bike when cold it runs until it gets warm then just dies but starts right back up. bike has run fine with the mods until just last week. anyone out there have any ideas or suggestions or does it sound like a warranty issue? thanks all



08 zx14se Brocks CT Duals, Brocks street map, Driven 16/43 sprockets,EK ZZZ Chain,MRA Windscreen, Roaring Toyz Diamond Cut Grips Pingel Elec shifter, Hyper-Pro RSC Damper, BlackChrome Wheels, Sargent Seat,Factory Pro Velocity Stacks,PCIII USB,Bonneville Pro, TPX Radar/Laser Detector, TPX Laser Jammer, Goodridge Shadow series braided lines front and rear, Rifleman 1/5 turn throttle, Fusion LED Stage IV Kit, DDM HID's 10,000k

Link | Top | Bottom

Hub


Hub's Gravatar

Joined: 02/05/09

Posts: 13719

RE: runnining issuses
07/21/09 9:47 AM

First thing is the map layer on the PC. Remove the hot side -THE HOT SIDE- Because the ground is still ground with the hot going to the ground on the injectors. So, hot off, take the idle check. Take off for a ride or wait to duplicate what you just said... Sorry, WATT you just said is I think it might be the map layer over the stock set is no set is set that up stock and now ride out your complaint.



Tormenting the motorcycling community one post at a time

Link | Top | Bottom

scottjkyl


scottjkyl's Gravatar

Location: east jordan,mi

Joined: 06/26/09

Posts: 1851

RE: runnining issuses
07/21/09 10:01 AM

so what r u suggesting? clear the maps on the pc3? and run at a stock set up?



08 zx14se Brocks CT Duals, Brocks street map, Driven 16/43 sprockets,EK ZZZ Chain,MRA Windscreen, Roaring Toyz Diamond Cut Grips Pingel Elec shifter, Hyper-Pro RSC Damper, BlackChrome Wheels, Sargent Seat,Factory Pro Velocity Stacks,PCIII USB,Bonneville Pro, TPX Radar/Laser Detector, TPX Laser Jammer, Goodridge Shadow series braided lines front and rear, Rifleman 1/5 turn throttle, Fusion LED Stage IV Kit, DDM HID's 10,000k

Link | Top | Bottom

scottjkyl


scottjkyl's Gravatar

Location: east jordan,mi

Joined: 06/26/09

Posts: 1851

RE: runnining issuses
07/23/09 9:13 AM

got it turns out all it was, was the harness from pc3 was not snapped in all the way to the bike connector was sliding in and out



08 zx14se Brocks CT Duals, Brocks street map, Driven 16/43 sprockets,EK ZZZ Chain,MRA Windscreen, Roaring Toyz Diamond Cut Grips Pingel Elec shifter, Hyper-Pro RSC Damper, BlackChrome Wheels, Sargent Seat,Factory Pro Velocity Stacks,PCIII USB,Bonneville Pro, TPX Radar/Laser Detector, TPX Laser Jammer, Goodridge Shadow series braided lines front and rear, Rifleman 1/5 turn throttle, Fusion LED Stage IV Kit, DDM HID's 10,000k

Link | Top | Bottom

Hub


Hub's Gravatar

Joined: 02/05/09

Posts: 13719

RE: runnining issuses
07/23/09 10:12 AM

This is where a Forum Room should be posted in "PC Q&A/And other Fuel Cutting Questions is Cut to the Chase" = Your Ass around and that 20/20 hindsight is so in your face. Subject title needs cleaning up, but if you want PC and the search is over ~ Click and ask the Fuel Cutters the Q and get Year A.

Can't blame DyeKnowJet is blame the installer. I just do not like to see the product bashed being the finger pointing is like a come pass right up your ASS if you are not careful is look who looks, "The Pay Per View![/b] = Look Closer?

No Way! "Plug GeTitINN ~ Plug It Inn!"

NO SHE???It


Chit Hap Pins = Like set the pins in the female ends DEEP PEER Pressure?
DieKnowJet = Pins not INN stall'd is one scenario on the 3wV = "Connectors Not the Snot Connected"

DyeKnowJet = Color wire not on the correct wire Tie-INN is the dangling dick = Head!
DiThinkDare4Eye Exam = Some snort a short is you smell some INN FUNNY?



Tormenting the motorcycling community one post at a time

Link | Top | Bottom


Welcome to zx14ninjaform.com!
 
New Topic Reply
Next Page

Page: 1

Previous Page

New Post

Please login to post a response.