I'll leave some post mod pics here for reference then add as it changes,
Midnight Sapphire Blue 12 FDF
OTD Pic
* Last updated by: 1400R on 8/18/2013 @ 2:29 AM *
Page: 1 2
Created on: 07/27/13 05:12 AM
Replies: 42
1400R
Location:
Joined: 07/25/13
Posts: 283
gobrian77
Location: Thailand
Joined: 04/30/13
Posts: 65
1400R
Location:
Joined: 07/25/13
Posts: 283
1400R
Location:
Joined: 07/25/13
Posts: 283
gobrian77
Location: Thailand
Joined: 04/30/13
Posts: 65
RE: Aussie FDF
07/29/13 2:01 AM
Little things, like a rear seat cowl instead of grab rails- I also didn't get a reflector (or mounting bracket) at the fork tube (though I believe that's a SE Asian thing)- looking forward to seeing how your bike progresses.
Make sure you change those heel guards or paint/powder-coat them black- it transforms the look from the side, IMHO.
Black1
Location: New York NY
Joined: 02/22/10
Posts: 1038
Grn14
Location: Montana
Joined: 02/25/09
Posts: 15511
1400R
Location:
Joined: 07/25/13
Posts: 283
1400R
Location:
Joined: 07/25/13
Posts: 283
cjuni
Location: Title Town MA
Joined: 06/12/11
Posts: 297
1400R
Location:
Joined: 07/25/13
Posts: 283
RE: Aussie FDF
08/10/13 3:12 PM
I'm not to sure on the C8/9's or the AA/FC.
The current FD definitely Don't require them for this mod.
One of the earlier models had an issue with a hard line but not sure which one.
Just reach in and make sure all the lines have slack and that you can move them.
Some early models have a zip tie that needs to be removed.
If you can move them by hand It should be all good.
1400R
Location:
Joined: 07/25/13
Posts: 283
RE: Aussie FDF
08/15/13 12:06 AM
The M4's finally arrived after doing their world tour of the US for 2 weeks.
Banged them on and boy are they nice. I don't think I'll even bother with the baffles just yet.
There loud on song but decent at idle.
I'll try to get a sound clip up later.
What where they thinking when these where drawn up.
I can actually see my chicken strips now and can get to work on them.
I can also get at the chain and rear wheel..
* Last updated by: 1400R on 8/15/2013 @ 12:08 AM *
Grn14
Location: Montana
Joined: 02/25/09
Posts: 15511
1400R
Location:
Joined: 07/25/13
Posts: 283
1coolbanana
Location:
Joined: 08/22/13
Posts: 28
1400R
Location:
Joined: 07/25/13
Posts: 283
Anrkizm95
Location: amarillo tx
Joined: 04/28/13
Posts: 46
1400R
Location:
Joined: 07/25/13
Posts: 283
1400R
Location:
Joined: 07/25/13
Posts: 283
RE: Aussie FDF
09/10/13 9:10 PM
I had hoped to get it back on the same dyno so the results would have been comparable.
I had to swap dyno's at the last minute because of issues.
it made 191.3 on one with stocks.
it made 190.6 on a different dyno without any baffles in the M4s
The only way now for me to give you a for sure is to fit the stocks and run again on the current dyno.
I can confirm the speed limiter in the Woolich Program works as well as the rev limit increase.
It went 318kph at 11.500.
Wolfman
Joined: 03/29/13
Posts: 6714
1400R
Location:
Joined: 07/25/13
Posts: 283
Wolfman
Joined: 03/29/13
Posts: 6714
Grn14
Location: Montana
Joined: 02/25/09
Posts: 15511
yannih
Location:
Joined: 11/08/12
Posts: 2167
RE: Aussie FDF
09/19/13 9:37 PM
Very nice...
Dont know about you but I found that Radiator gaurd a royal pain to install properly.
Also if youre interested, we ride quite a bit (2 x ZX-14, 2007 and 2012) so let me know.
1400R
Location:
Joined: 07/25/13
Posts: 283
RE: Aussie FDF
09/20/13 5:03 PM
I didn't find it all that difficult Yannih.
I did fit the bolt in reverse which made it easy but I used a small 1/4 inch drive on the front rim side.
While holding the rear side with the hex head.
I never even had to turn the handle bars and left it on the side stand.
Get onto me when you next out for a punt and I'll see if works going to get in the way.
I work some weird hours man.
The Sydney Drags are running a Bike Night on the 10th October which is a Thursday.
$55 entry.
Should see if we can get a group of us going.
Page: 1 2
New Post
Please login to post a response.